Quantenna Mini U-Boot Version: v36.7.0.30 Built: Aug 08 2016 at 16:56:14 QTN-EMAC Using 'ipaddr' from early config: 169.254.1.2 Using 'serverip' from early config: 169.254.1.1 1G-FD Using QTN-EMAC device TFTP from server 169.254.1.1; our IP address is 169.254.1.2 Filename 'u-boot.bin'. Load address: 0x88000000 Loading: *A2 A3 A4 A5 T A2 A3 A4 A5 T A2 A3 A4 A5 T A2 A3 A4 A5 T A2 A3 A4 A5 Retry count exceeded; starting again 1G-FD Using QTN-EMAC device TFTP from server 169.254.1.1; our IP address is 169.254.1.2 Filename 'u-boot.bin'. Load address: 0x88000000 Loading: *A2 A3 A4 A5 T A2 A3 A4 A5 T A2 A3 A4 A5 T A2 A3 A4 A5 T A2 A3 A4 A5 Retry count exceeded; starting again 1G-FD Using QTN-EMAC device TFTP from server 169.254.1.1; our IP address is 169.254.1.2 Filename 'u-boot.bin'. Load address: 0x88000000 Loading: *A2 A3 A4 A5 T A2 A3 A4 A5 T ############## done Bytes transferred = 68464 (0x10b70) Boot reached stage 13 Boot reached stage 12 Valid CRC found in flash restoring env... Boot reached stage 11 Quantenna secondary U-Boot: U-Boot 2009.06.AEI-cp-36-7-1-23-dirty (Nov 30 2016 - 11:35:08) hw_config_id 65535: 'QHS840_5S1' Cold boot Reset status: 0x00000001 Info: data uncached: addr=0xc0000000 size=1024MB Info: text at 0x88040000, stack at 0x88013ffc(8192), heap at 0x88000000(73728), uboot size 170152 Info: i-cache is enabled Info: d-cache is enabled Info: CPU freq is 500000000, dev freq is 125000000 Info: Quantenna U-Boot version:v37.4.0.29 Info: build date 'Nov 30 2016', time '11:35:00' SPI flash info: name : mx25l512e jedec_id : 0xc22010 sector size : 4096 number of sector : 16 frequency : 104000000 flags : 0x2 lock : DDR_INIT: type = 16, speed = 2, size = 134217728 500MHz BDA at 0x80002000 In: serial Out: serial Err: serial Boot reached stage 64 Boot reached stage 65 br Hit ESC key to stop autoboot: 1 0 Boot reached stage 80 1G-FD 1G-FD Using br device TFTP from server 169.254.1.1; our IP address is 169.254.1.2 Filename 'topaz-linux.lzma.img'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################ done Bytes transferred = 5133977 (0x4e5699) Boot reached stage 81 Boot reached stage 84 Boot reached stage 1 ## Booting kernel from Legacy Image at 83000000 ... Boot reached stage 2 Boot reached stage 3 Image Name: topaz-linux Image Type: arc Linux Kernel Image (lzma compressed) Data Size: 5125785 Bytes = 4.9 MB Load Address: 8493a000 Entry Point: 8493a000 Qtn flags: 00000001 Verifying Checksum ... OK Boot reached stage 4 Boot reached stage 5 Boot reached stage 6 Boot reached stage 14 Uncompressing Kernel Image ... OK Boot reached stage 7 Boot reached stage 8 Command line TAG setup Params->u.cmdline.cmdline console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535 p console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535 ## Unset TAG qtn_flags 1 ## Transferring control to Linux (at address 8493a000) ATAG parameters 88066fb0 - 88067008... [ 0.000000] Linux version 2.6.35.12 (ppark@new-host-2.home) (gcc version 4.2.1 (ARC_2.3)) #2 Mon Jan 22 17:51:45 PST 2018 [ 0.000000] Parsing ATAG parameters from bootloader [ 0.000000] ATAG_CORE: successful parsing [ 0.000000] ATAG_CMDLINE: command line = console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535 [ 0.000000] Board id: 65535 [ 0.000000] ATAG_HW_CONFIG_ID: hw_config_id = 65535 [ 0.000000] [ 0.000000] Processor Family: ARC 700 [0x33] [ 0.000000] CPU speed : 500.00 Mhz [ 0.000000] Timers: TIMER1 TIMER0 [ 0.000000] Interrupt Vect Base: 0x88052000 [ 0.000000] Peripheral Base: NOT present; assuming 0xCOFC0000 [ 0.000000] Data UNCACHED Base (I/O): start 0xc0 Sz, 1024 MB [ 0.000000] ARC700 MMU Ver [2] [ 0.000000] PAGE SIZE 8k [ 0.000000] JTLB 128 x 2 = 256 entries [ 0.000000] uDTLB 8 entr, uITLB 4 entr [ 0.000000] TLB Refill "will NOT" Flush uTLBs [ 0.000000] Detected I-cache : [ 0.000000] Type=2 way set-assoc, Line length=32, Size=16K (enabled) [ 0.000000] Detected D-cache : [ 0.000000] Type=4 way set-assoc, Line length=32, Size=16K (enabled) [ 0.000000] Extensions: [ 0.000000] MPY: 32x32 with ANY Result Reg MAC MPY: Dual 16 x 16 and 32 x 16 [ 0.000000] DCCM: N/A ICCM: N/A [ 0.000000] CRC: N/A, SWAP: Present NORM: Present [ 0.000000] Min-Max: Present, Barrel Shifter: Present [ 0.000000] Ext Arith Insn: Present [ 0.000000] Floating Point Extension: N/A [ 0.000000] On node 0 totalpages: 16383 [ 0.000000] free_area_init_node: node 0, pgdat 8589dd44, node_mem_map 8594e024 [ 0.000000] Normal zone: 72 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16311 pages, LIFO batch:3 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16311 [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535 [ 0.000000] bootconsole [ruby_early0] enabled [ 0.000000] PID hash table entries: 512 (order: -2, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 3, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 2, 32768 bytes) [ 0.000000] Memory: 38872KB available (2160K code,1207K data, 13088K init) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU debugfs-based tracing is enabled. [ 0.000000] Verbose stalled-CPUs detection is disabled. [ 0.000000] clockevent mode switch to [1] [ 0.000000] clockevent mode switch to [2] [ 0.000000] Calibrating delay loop... 249.03 BogoMIPS (lpj=622592) [ 0.115000] pid_max: default: 4096 minimum: 301 [ 0.120000] Mount-cache hash table entries: 1024 [ 0.125000] Starting run_ksoftirqd, stack (thread_info) at 858c2000 cpu 0 [ 0.130000] NET: Registered protocol family 16 [ 0.135000] Topaz heap in SRAM 88016780<->88020000, B2 BASE 17800 [ 0.150000] bio: create slab at 0 [ 0.155000] watch64: 2003/08/22 Josef 'Jeff' Sipek [ 0.160000] watch64: Enabling Watch64 extensions...done. [ 0.165000] Switching to clocksource ARC Timer1 [ 0.175000] NET: Registered protocol family 2 [ 0.180000] IP route cache hash table entries: 2048 (order: 0, 8192 bytes) [ 0.185000] TCP established hash table entries: 4096 (order: 2, 32768 bytes) [ 0.190000] TCP bind hash table entries: 4096 (order: 1, 16384 bytes) [ 0.195000] TCP: Hash tables configured (established 4096 bind 4096) [ 0.200000] TCP reno registered [ 0.205000] NET: Registered protocol family 1 [ 0.725000] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.730000] msgmni has been set to 75 [ 0.735000] io scheduler noop registered (default) [ 1.165000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled [ 1.175000] serial8250.0: ttyS0 at MMIO 0xf0000000 (irq = 48) is a 16550A [ 1.180000] console [ttyS0] enabled, bootconsole disabled [ 1.180000] console [ttyS0] enabled, bootconsole disabled [ 1.190000] brd: module loaded [ 1.200000] loop: module loaded [ 1.205000] spi_flash: Force not to support Protect Mode [ 1.210000] Creating 3 MTD partitions on "spi_flash": [ 1.215000] 0x000000000000-0x000000005000 : "uboot" [ 1.220000] 0x000000005000-0x00000000b000 : "uboot_env" [ 1.230000] 0x00000000b000-0x000000010000 : "data" [ 1.235000] spi_flash: SPI flash driver initialized successfully! [ 1.240000] ruby_health loading [ 1.240000] HBM pool: emac rx 0x0 to 0x8000, wmac rx 0x8000 to 0xa000 [ 1.760000] HBM meta: emac rx 0x63c040 to 0x6bc040, wmac rx 0x6bc080 to 0x6dc080 [ 1.765000] topaz_hbm_init_pool_list pool 0 pool_list 0x88000000 bus_range 0x6ec400 to 0x26ec400 sz 4096 count 8192 [ 1.765000] topaz_hbm_init_pool_list pool 1 pool_list 0x88008000 bus_range 0x26fc400 to 0x48fc400 sz 17408 count 2048 [ 1.765000] topaz_hbm_init_pool_list pool 3 pool_list 0x8800a000 bus_range 0x0 to 0x0 sz 0 count 4096 [ 1.770000] topaz_busmon_init success [ 1.770000] topaz_temp_sens_init success [ 1.775000] u32 classifier [ 1.780000] input device check on [ 1.785000] Actions configured [ 1.785000] Netfilter messages via NETLINK v0.30. [ 1.790000] nf_conntrack version 0.5.0 (607 buckets, 2428 max) [ 1.800000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.805000] TCP cubic registered [ 1.805000] NET: Registered protocol family 10 [ 1.815000] NET: Registered protocol family 17 [ 1.820000] 802.1Q VLAN Support v1.8 Ben Greear [ 1.825000] All bugs added by David S. Miller [ 1.840000] Freeing unused kernel memory: 13088k freed [8493a000] TO [85602000] [ 1.845000] Common mmap addr-space starts 2c0f0000 init started: BusyBox v1.10.3 (2018-01-22 17:33:12 PST) starting pid 41, tty '': '/etc/init.d/rcS' [ 2.160000] load_module: 'bootcfg' using DRAM (offset:0x863e0000, size:0x8e44) Starting portmap: done Initializing random number generator... done. Starting network... [ 2.905000] load_module: 'fwt_if' using DRAM (offset:0x85a28000, size:0x1684) [ 2.930000] load_module: 'switch_vlan' using DRAM (offset:0x85a3c000, size:0x2751) [ 2.985000] load_module: 'switch_tqe' using DRAM (offset:0x85a68000, size:0x58ff) [ 3.035000] tqe_descs_alloc: 2048 tqe_rx_descriptors at kern uncached 0x580b0788 bus 0x80016788 [ 3.075000] load_module: 'fwt_ctrl' using DRAM (offset:0x864c0000, size:0x236a1) [ 3.080000] fwt_ctrl: module license 'Proprietary' taints kernel. [ 3.085000] Disabling lock debugging due to kernel taint [ 3.190000] load_module: 'rtl8367b' using DRAM (offset:0x86500000, size:0x32a47) [ 3.250000] load_module: 'emaclib' using DRAM (offset:0x86480000, size:0x53d9) [ 3.460000] load_module: 'dpi' using DRAM (offset:0x85a3a000, size:0x1b89) [ 3.490000] load_module: 'switch_emac' using DRAM (offset:0x8648c000, size:0x213b), SRAM (offset:0x8801eda8, size:0x1d0) [ 3.560000] emac wbsp: 0 [ 3.560000] enable A2 (bonded) [ 3.620000] topaz_emac_init, emac0 [ 3.625000] Random stuff 29 [ 3.630000] topaz_emac_init, emac1 emac0 is eth1_1, emac1 is eth1_0 Stateless mode. Using temporary ip address: Using IP address 169.254.1.2 Netmask is not set cat: can't open '/mnt/jffs2/eth_macaddr': No such file or directory BusyBox v1.10.3 (2018-01-22 17:33:12 PST) multi-call binary Usage: ifconfig [-a] interface [address] Configure a network interface Options: [add ADDRESS[/PREFIXLEN]] [del ADDRESS[/PREFIXLEN]] [[-]broadcast [ADDRESS]] [[-]pointopoint [ADDRESS]] [netmask ADDRESS] [dstaddr ADDRESS] [hw ether ADDRESS] [metric NN] [mtu NN] [[-]trailers] [[-]arp] [[-]allmulti] [multicast] [[-]promisc] [txqueuelen NN] [[-]dynamic] [up|down] ... [ 3.945000] load_module: 'bonding' using DRAM (offset:0x86580000, size:0x11bd9) [ 3.995000] bonding: Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009) [ 4.000000] bonding: MII link monitoring set to 10000 ms [ 4.030000] emac_lib eth1_0: force link (1000/Full) [ 4.050000] emac_lib eth1_1: force link (1000/Full) [ 4.070000] ADDRCONF(NETDEV_UP): bond0: link is not ready [ 4.075000] bonding: bond0: Adding slave eth1_0. [ 4.080000] emac_lib eth1_0: force link (1000/Full) [ 4.085000] bonding: bond0: enslaving eth1_0 as an active interface with an up link. [ 4.090000] ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready [ 4.095000] bonding: bond0: Adding slave eth1_1. [ 4.100000] emac_lib eth1_1: force link (1000/Full) [ 4.110000] bonding: bond0: enslaving eth1_1 as an active interface with an up link. [ 4.210000] device bond0 entered promiscuous mode [ 4.215000] device eth1_0 entered promiscuous mode [ 4.220000] device eth1_1 entered promiscuous mode [ 4.250000] br0: port 1(bond0) entering forwarding state [ 4.255000] br0: port 1(bond0) entering forwarding state /sbin/ifup -a Version of /proc/bootcfg/qtn_regulatory_db.bin is Regulatory db version: v0 Version of /etc/qtn_regulatory_db.bin is Regulatory db version: v37.4.0.60 Selected database version: Regulatory db version: v37.4.0.60 Using /etc/qtn_regulatory_db.bin Starting qevt_server Starting inetd ... ################################################# # Actiontec QTN disable httpd call_qcsapi get_gpio_config 1 = 2 ################################################# [ 5.420000] load_module: 'hw_rev' using DRAM (offset:0x86574000, size:0x36d0) Starting wireless... [ 5.525000] FWT: [10:78:5b:REDACTED] add entry, port:emac0 node:0 entries:1 Configuration has been set to default values. Reboot after customizing to ensure correct operation. complete /scripts/cmdloop starting /sbin/qcsapi_rpcd, at 00:00:06 up 0 min, load average: 0.08, 0.01, 0.00 /scripts/cmdloop starting /sbin/call_qcsapi_rpcd, at 00:00:07 up 0 min, load average: 0.08, 0.01, 0.00 'monitor_temperature' is not enabled/set AUI Service started.... Starting ntpclient /scripts/cmdloop starting /sbin/qharvestd, at 00:00:08 up 0 min, load average: 0.08, 0.01, 0.00 httpd is not enabled Jan 1 00:00:08 qharvestd[480]: qharvestd[notice]: qharvestd v1.29 started starting pid 518, tty '/dev/console': 'getty 115200 ttyS0' Welcome to the Erik's uClibc development environment. soc1 login: /scripts/readmem: line 10: cannot create /proc/wlanmem: nonexistent directory cat: can't open '/proc/wlanmem': No such file or directory Starting console_config... Starting console_config... Using IP address 169.254.1.2 Using netmask 255.255.255.252 Added static ARP for BHR bridge interface Loading modules [ 13.745000] load_module: 'qtn_debug' using DRAM (offset:0x85a72000, size:0x403) [ 13.885000] load_module: 'i2cbus' using DRAM (offset:0x85a74000, size:0x1ce2) [ 14.085000] load_module: 'qtsens' using DRAM (offset:0x85a72800, size:0x7b6) [ 14.240000] load_module: 'pm_interval' using DRAM (offset:0x86550000, size:0x13b2) [ 14.480000] load_module: 'wlan' using DRAM (offset:0x86700000, size:0x9ebf1) [ 14.540000] bond0: no IPv6 routers present [ 14.860000] <<<== [nbr_ap_list_init:8849] [ 14.860000] wlan: 0.8.4.2 (0.9.3.3) [ 15.195000] load_module: 'auc_fw' using DRAM (offset:0x8788c040, size:0x115b) [ 15.415000] load_module: 'radar' using DRAM (offset:0x85b00000, size:0x1a394) [ 15.520000] load_module: 'qvspmod' using DRAM (offset:0x85b60000, size:0x10dd9) [ 15.675000] load_module: 'qdrv' using DRAM (offset:0x87400000, size:0x9faf1) [ 16.240000] qdrv wbsp: 0 [ 16.405000] load_module: 'wlan_xauth' using DRAM (offset:0x85bb7400, size:0x32f) [ 16.605000] load_module: 'wlan_ccmp' using DRAM (offset:0x8660e000, size:0x1782) [ 16.830000] load_module: 'wlan_tkip' using DRAM (offset:0x865f8000, size:0x2636) Loading MuC driver (qtn_driver.qtn_ruby.0.bin) Waiting for Wireless Events from interfaces... Found power table in /etc/power_tables [ 18.430000] QDRV: power table checksum for /etc/power_tables/tx_power_QSR1000_ca.txt [ 18.475000] QDRV: power table checksum for /etc/power_tables/tx_power_QSR1000_ca_fcc.txt [ 18.520000] QDRV: power table checksum for /etc/power_tables/tx_power_QSR1000_eu.txt [ 18.560000] QDRV: power table checksum for /etc/power_tables/tx_power_QSR1000_us.txt [ 18.980000] set power_selection 3 [ 18.990000] qdrv_soc_publish_params: parames->tqe_sem_en 0, auc_tqe_sem_en 0 [ 18.995000] ..... Current RFIC Chip ID -- 0 [ 19.285000] AuC SRAM start 0x88040000 end 0x88070000 size 196608 [ 19.290000] AuC is configured for MU-enabled SRAM layout [ 19.295000] AuC SRAM bank 0 start 0x88040000 end 0x88050000 [ 19.300000] AuC SRAM bank 1 start 0x88050000 end 0x88060000 [ 19.305000] AuC SRAM bank 2 start 0x88060000 end 0x88070000 [ 19.390000] MuC: g_tqe_sem_en 0 [ 19.390000] MuC: build date Fri, 21 Oct 2016 18:02:00 -0700 [ 19.395000] MuC: slow heap begin=0x00222e00 end=0x0039fe00 [ 19.400000] MuC: fast heap begin=0x80030800 end=0x80037000 [ 19.405000] MuC: stack start=0x8003efc0 sp=0x8003f724 [ 19.410000] MuC: calstate is 3 (prod), dcache on [ 19.415000] MuC: RFIC version 1 rev 0 [ 19.440000] qdrv_mac_reserve_clear: mac reservation table cleared [ 19.465000] qdrv_mu_stat_init [ 19.485000] MuC: bb_init: FEM 0x5 bw_mode 0 chan 0 11b 0 11a 1 [ 19.490000] MuC: rf_optimizing_rf_register_map, set rf to 0x75 [ 19.495000] MuC: os_uc, after bb_rf_complete_attach. [ 19.500000] MuC: WMAC0: hal fd start=0xe5040300 count=48 size=108 end=0xe5041740 [ 19.505000] MuC: WMAC1: hal fd start=0xe5140d50 count=8 size=84 end=0xe5140ff0 [ 19.510000] MuC: dynamic one-bit autocorrelation enabled [ 19.515000] MuC: freq 1 proj 1 [ 19.520000] MuC: QMAT SRAM base 0x80070000 [ 19.520000] MuC: enable IRQs [ 19.525000] MuC: AuC enabled 0xe5101b70/0x6005b0b8 il 0xe510122c/0xe5101230 stats 0x600591f8/0x6005adf80x6006e3c4 [ 19.530000] MuC: Can't allocate more fcs for AuC. Bad... WMAC = 1 [ 19.535000] MuC: Update MU debug flag from 0x00000000 to 0x20000000 [ 19.540000] AuC: Update mu flag : 0x20000000. Max delay = 0 [ 19.545000] QDRV: I2C dapter not found [ 19.575000] QDRV: hardware is 4x4 11ac FO RGMII/PCIe QV840 [ 19.580000] MuC boot succeeded 0.110 seconds [ 20.085000] load_module: 'wlan_scan_ap' using DRAM (offset:0x85da4000, size:0x2c1a) [ 20.245000] MuC: freq 1 proj 1 [ 20.250000] MuC: qtn_mu_ndpa_setup: bw_cap 2 done [ 20.275000] VAP create succeeded 0.020 seconds [ 20.285000] MuC: qtn_mu_ndpa_setup: bw_cap 2 done [ 20.745000] MuC: calibration ver 0x801 neigh_repo set to 1 radar in 80MHZ mode Setting mode to 11ac80 [ 22.405000] channel 140 is added into non-primary channel list [ 22.415000] channel 144 is added into non-primary channel list radar start with[ 22.440000] DFS_s_radio: parameters updated, region: us regulatory us dfs_s_radio 0 dfs 0 non-dfs 0 scan 0 auto-channel channel 0 Configure max_boot_cac to -1 [ 23.705000] device wifi0 entered promiscuous mode [ 23.825000] Enabling SSDP flooding Beamforming enabled [ 24.565000] Enabling SCS SCS enabled QTM: load profile off [ 24.810000] qvsp_strm_reset: stream reset QTM enabled: 0 [ 25.720000] BRIDGE WLAN report flood-forwarding enabled QCS API error 1010: Cannot contact security manager No core dump generated monitor led [ 27.345000] Build name: v37.4.0.89 [ 27.345000] Build revision: 52506 [ 27.350000] Build type: SDK [ 27.355000] Build timestamp: 1477098800 [ 27.360000] Platform ID: 432 [ 27.365000] Hardware ID: QV840 [ 27.370000] Hardware revision: bbic4_rev_a2 [ 27.370000] Band: 5GHz [ 27.375000] Kernel version: 2.6.35 [ 27.380000] Calibration version: disabled [ 27.385000] DC/IQ cal version: V8.1 [ 27.390000] Power cal version: V8.1 [ 27.390000] MuC firmware: qtn_driver.qtn_ruby.0.bin [ 27.395000] DSP firmware: rdsp_driver.0.bin [ 27.400000] AuC firmware: auc_driver.default.0.bin [ 27.405000] MAC address 0: 10:78:5b:e0:07:96 [ 27.410000] MAC address 1: 00:00:00:00:00:00 [ 27.415000] U-Boot version: v37.4.0.29 Carrier ID 0, uboot update flag 0 complete [ 28.085000] MuC: Update MU debug flag from 0x20000000 to 0x00000000 [ 28.085000] MuC: MU enabled [ 28.085000] AuC: Update mu flag : 0x00000000. Max delay = 0 Added static ARP for BHR bridge interface [ 29.560000] MuC: #RX data path optimal flag 0 [ 29.565000] MuC: rx_post_init: free 0 rxq 9 9 394 descr 0x8000f000/6592 cache 0x8002caa0/13184 [ 29.565000] MuC: auto cs is enabled [ 29.570000] WPS: push button GPIO pin 4 [ 29.570000] WPS: monitored using polling [ 29.570000] WPS: active logic is low [ 29.595000] br0: port 2(wifi0) entering forwarding state [ 29.595000] br0: port 2(wifi0) entering forwarding state hostapd is not running wpa_supplicant is not running start-prod: adding default "manufacturer=Quantenna" to /mnt/jffs2/hostapd.conf start-prod: adding default "device_name=Reference Design" to /mnt/jffs2/hostapd.conf start-prod: adding default "model_name=Topaz" to /mnt/jffs2/hostapd.conf start-prod: adding default "model_number=QV840.432" to /mnt/jffs2/hostapd.conf start-prod: adding default "serial_number=10785BE00796" to /mnt/jffs2/hostapd.conf start-prod: adding default "friendly_name=UPnP Access Point" to /mnt/jffs2/hostapd.conf start-prod: adding default "device_type=6-0050F204-1" to /mnt/jffs2/hostapd.conf Enable ap pin setup in all BSSes [ 31.145000] br0: port 2(wifi0) entering forwarding state /scripts/cmdloop starting /sbin/qharvestd, at 00:00:31 up 0 min, load average: 0.63, 0.15, 0.05 [ 32.160000] br0: port 2(wifi0) entering forwarding state [ 32.160000] br0: port 2(wifi0) entering forwarding state [ 33.590000] br0: port 2(wifi0) entering forwarding state [ 33.860000] MuC: freq 1 proj 1 [ 33.875000] VAP create succeeded 0.010 seconds [ 33.910000] device wifi1 entered promiscuous mode [ 34.900000] br0: port 3(wifi1) entering forwarding state [ 34.900000] br0: port 3(wifi1) entering forwarding state [ 35.990000] br0: port 3(wifi1) entering forwarding state [ 36.295000] MuC: freq 1 proj 1 [ 36.315000] VAP create succeeded 0.010 seconds [ 36.350000] device wifi2 entered promiscuous mode [ 37.340000] br0: port 4(wifi2) entering forwarding state [ 37.340000] br0: port 4(wifi2) entering forwarding state [ 38.450000] br0: port 4(wifi2) entering forwarding state [ 38.705000] MuC: freq 1 proj 1 [ 38.725000] VAP create succeeded 0.010 seconds [ 38.760000] device wifi3 entered promiscuous mode [ 39.850000] br0: port 5(wifi3) entering forwarding state [ 39.850000] br0: port 5(wifi3) entering forwarding state [ 40.905000] br0: port 5(wifi3) entering forwarding state [ 42.510000] MuC: Update MU debug flag from 0x00000000 to 0x20000000 [ 42.510000] MuC: MU disabled [ 42.510000] AuC: Update mu flag : 0x20000000. Max delay = 0 [ 43.315000] RADAR: CAC started for channel 52 (5260 MHz) radar start with regulatory us [ 44.140000] Disabling SCS [ 44.930000] RADAR: CAC stopped for channel 52 (5260 MHz) [ 44.935000] br0: port 2(wifi0) entering forwarding state [ 44.935000] br0: port 2(wifi0) entering forwarding state [ 45.230000] br0: port 5(wifi3) entering forwarding state [ 45.230000] br0: port 5(wifi3) entering forwarding state [ 50.625000] RADAR: CAC started for channel 136 (5680 MHz) Stopping MAUI service Starting qevt_server QEVT: failed to initialise server socket: Address already in use [ 120.800000] Channel Status Status_string [ 120.800000] 36 2 Available [ 120.800000] 40 2 Available [ 120.800000] 44 2 Available [ 120.800000] 48 2 Available [ 120.800000] 52 8 Not-Available-CAC-Required [ 120.800000] 56 8 Not-Available-CAC-Required [ 120.800000] 60 8 Not-Available-CAC-Required [ 120.800000] 64 8 Not-Available-CAC-Required [ 120.800000] 100 8 Not-Available-CAC-Required [ 120.800000] 104 8 Not-Available-CAC-Required [ 120.800000] 108 8 Not-Available-CAC-Required [ 120.800000] 112 8 Not-Available-CAC-Required [ 120.800000] 132 2 Available [ 120.800000] 136 2 Available [ 120.800000] 140 2 Available [ 120.800000] 144 2 Available [ 120.800000] 149 2 Available [ 120.800000] 153 2 Available [ 120.800000] 157 2 Available [ 120.800000] 161 2 Available [ 120.800000] RADAR: CAC completed for channel 136 (5680 MHz)